Universal flexible suction arm installation
2023-12-24 13:07:11
1. There are two flanges and matching Screws in the upper door of the chassis. Take it out and install it on the air inlet at the top of the device.
2. Put the sealing rubber ring (black rubber apron) in the accessory box on the flange of the first installation equipment.
3. Stretch the skeleton of the inhalation arm as straight as possible and place a hose clamp on the suction hood.
4, the steel wire wind pipe sleeve on the inhalation arm, try to straighten out, cut the excess part (too much folds and bends will increase the wind resistance), one end of the wind pipe is set on the suction hood, the other end On the connecting flange, both ends are fixed with hose clamps.
5. Install the suction cylinder skeleton into the flange of the equipment. The gap between the equipment flange and the suction arm connecting flange shall be sealed with a sealing rubber ring.
There is a need to consult Qingdao Su Shiqi manufacturing company 18562630882 QQ
Welding fume components and hazards 1. Stainless steel welding fumes: chromium and nickel compounds in the smoke, not only can cause welding pneumoconiosis, but also a powerful carcinogen. 2. Heavy metal manganese poisoning: pollution caused by welding fumes, resulting in autonomic dysfunction, serious poisoning can not take care of themselves; 3, carbon monoxide ozone: is a suffocating harmful gas, leading to phrenic nervous system diseases, high concentrations of inhalation can suffocate death; 4 Oxygen compounds of nitrogen: Digested into the human body through respiration, causing pulmonary blood system diseases, long-term effects cause neurasthenia; need to consult Qingdao Su Shiqi Manufacturing Company 18562630882 QQ
Control of welding fumes and harmful gases Control of welding fumes and harmful gases There are two ways to control the transmission route: full ventilation and local exhaust. Total ventilation is also called dilution ventilation. It uses clean air to dilute the concentration of harmful substances in the indoor air so that the concentration of harmful substances in the indoor air does not exceed the maximum allowable concentration specified in the hygiene standards. At the same time, the polluted air is continuously discharged to the outside or collected and purified. . Total ventilation includes natural ventilation and mechanical ventilation in two ways [3]. In foreign countries, natural ventilation is generally used for outdoor welding operations or open space welding, and mechanical ventilation is usually used for indoor operations. Through the axial fan mounted on the wall or ceiling, the welding fumes in the workshop are discharged to the outside, or purified through a purifier, and recycled in the workshop to achieve the purpose of reducing the fume concentration in the workshop. The purified air is recycled to solve the energy loss in the workshop. This method is commonly used abroad. Partial ventilation is the treatment of local air flow so that local work sites are not contaminated by harmful substances and maintain a good air environment. The general local exhaust fan group consists of four parts: a hood, a duct, a purification system, and a fan. Local exhaust air can be divided into fixed local exhaust system and mobile local exhaust system according to different gas collection methods. The fixed local exhaust system is mainly used in the large-scale welding production workshop where the operation site and the worker's operation mode are fixed, and the position of the gas gathering hood can be fixed at one time according to the actual situation. The mobile local exhaust system has a relatively flexible working status and can adopt different working postures according to different working conditions to ensure the processing efficiency and the convenience of the operators. The purification system for welding fumes and harmful gases is usually a combination of bag type or electrostatic dust removal combined with an adsorbent, which has high processing efficiency and stable working conditions. Electrostatic smoke purifier, mobile welding fume purifier, polished dust bench, moxibustion fume purifier, universal flexible suction arm, joint arm, activated carbon adsorption box, garage exhaust gas purification device, UV photocatalytic equipment, low temperature plasma deodorization Equipment need to consult Qingdao Su Shiqi manufacturing company 18562630882 QQ
2. Put the sealing rubber ring (black rubber apron) in the accessory box on the flange of the first installation equipment.
3. Stretch the skeleton of the inhalation arm as straight as possible and place a hose clamp on the suction hood.
4, the steel wire wind pipe sleeve on the inhalation arm, try to straighten out, cut the excess part (too much folds and bends will increase the wind resistance), one end of the wind pipe is set on the suction hood, the other end On the connecting flange, both ends are fixed with hose clamps.
5. Install the suction cylinder skeleton into the flange of the equipment. The gap between the equipment flange and the suction arm connecting flange shall be sealed with a sealing rubber ring.
There is a need to consult Qingdao Su Shiqi manufacturing company 18562630882 QQ
Welding fume components and hazards 1. Stainless steel welding fumes: chromium and nickel compounds in the smoke, not only can cause welding pneumoconiosis, but also a powerful carcinogen. 2. Heavy metal manganese poisoning: pollution caused by welding fumes, resulting in autonomic dysfunction, serious poisoning can not take care of themselves; 3, carbon monoxide ozone: is a suffocating harmful gas, leading to phrenic nervous system diseases, high concentrations of inhalation can suffocate death; 4 Oxygen compounds of nitrogen: Digested into the human body through respiration, causing pulmonary blood system diseases, long-term effects cause neurasthenia; need to consult Qingdao Su Shiqi Manufacturing Company 18562630882 QQ
Control of welding fumes and harmful gases Control of welding fumes and harmful gases There are two ways to control the transmission route: full ventilation and local exhaust. Total ventilation is also called dilution ventilation. It uses clean air to dilute the concentration of harmful substances in the indoor air so that the concentration of harmful substances in the indoor air does not exceed the maximum allowable concentration specified in the hygiene standards. At the same time, the polluted air is continuously discharged to the outside or collected and purified. . Total ventilation includes natural ventilation and mechanical ventilation in two ways [3]. In foreign countries, natural ventilation is generally used for outdoor welding operations or open space welding, and mechanical ventilation is usually used for indoor operations. Through the axial fan mounted on the wall or ceiling, the welding fumes in the workshop are discharged to the outside, or purified through a purifier, and recycled in the workshop to achieve the purpose of reducing the fume concentration in the workshop. The purified air is recycled to solve the energy loss in the workshop. This method is commonly used abroad. Partial ventilation is the treatment of local air flow so that local work sites are not contaminated by harmful substances and maintain a good air environment. The general local exhaust fan group consists of four parts: a hood, a duct, a purification system, and a fan. Local exhaust air can be divided into fixed local exhaust system and mobile local exhaust system according to different gas collection methods. The fixed local exhaust system is mainly used in the large-scale welding production workshop where the operation site and the worker's operation mode are fixed, and the position of the gas gathering hood can be fixed at one time according to the actual situation. The mobile local exhaust system has a relatively flexible working status and can adopt different working postures according to different working conditions to ensure the processing efficiency and the convenience of the operators. The purification system for welding fumes and harmful gases is usually a combination of bag type or electrostatic dust removal combined with an adsorbent, which has high processing efficiency and stable working conditions. Electrostatic smoke purifier, mobile welding fume purifier, polished dust bench, moxibustion fume purifier, universal flexible suction arm, joint arm, activated carbon adsorption box, garage exhaust gas purification device, UV photocatalytic equipment, low temperature plasma deodorization Equipment need to consult Qingdao Su Shiqi manufacturing company 18562630882 QQ
Screws
The product range of Hongchuang hardware fasteners includes hexagon head screws, full thread and half thread hexagon socket head cap screws, hexagon wood screws, hexagon socket head cap screws, full thread and half thread hexagon socket countersunk head screws, hexagon socket head flange screws, set screws, etc. We provide products conforming to DIN, ANSI and JIS standards.
Stainless steel of grade 304 contains nickel of 8% and chromium of 18% and is the most commonly used grade for the production of fasteners. It possesses an excellent combination of strength, corrosion resistance and fabricability. Fasteners of this grade are being extensively used today in almost every industry.
Metal Screw,Self Tapping Screws,Stainless Steel Screws,Steel Screws
Taizhou Hongchuang Hardware Co., Ltd. , https://www.taizhouhongchuang.com