Renovation of the installation of gas stoves for literacy
The installation of gas stoves is something that we should consider when we renovate the kitchen. In addition, the size of the gas stove also affects the size of the holes in the cabinet panel. Therefore, when the cabinet is installed, we must determine the type of gas stove and the specific The model is the only way to make the subsequent installation smooth. In addition, if the gas stove is not installed, please ask a professional master to operate it, so as to avoid danger caused by improper operation by yourself.
| Gas stove installation meaning |
The gas stove is a kitchen appliance that has a very high utilization rate in daily life, and also has a very high safety requirement. Sometimes we buy one from the Internet, but do not know how to install it. In fact, the installation of the gas stove is quite simple. It may be difficult to adjust the fire if it is difficult. If your home kitchen has just been renovated, you are also prepared to use the embedded gas. The stove, and the stove has not been opened, this time after you choose a gas stove, you must open the hole in the stove according to the size of the opening of the stove reminded to ensure the smooth installation of the gas stove.
| Gas stove installation process |
The first step is to install the gas pipe.
Before installing the gas pipe, we need to put the cooker into the well-burning stove. See the figure below.
The second step is to clean the air inlet of the cooking appliance, and then place the hose fitting into the cooker joint beyond the red line (see the following figure), and use a pipe clamp or pipe clamp to clamp the hose.
The third step, check whether the battery box has a battery, if not buy the battery and install it, usually a 1 battery.
After this basic installation is completed, you begin to turn on the knob to test whether there is a fire, or to see if the color of the flame is light blue. If the color of the flame is yellowish or reddish, you need to debug the gas stove.
The fourth step is to debug the gas stove so that its flame will appear normal color, ie light blue as shown in the figure below.
| Gas stove installation precautions |
After the gas stove is bought home, you need to pay attention to the precautions before installation.
First, after unpacking, please carefully check whether the product accessories are complete or not according to the packing list. If you find a problem, contact your dealer for replacement.Secondly, please check whether the type of gas you use is in accordance with the type of gas marked on the product. If it does not comply with the type of gas, it is strictly prohibited to install (the type of gas is marked on the nameplate and outer package of the bottom case).
Third, check whether the components of the product are correctly installed and the screws are tight, to avoid possible damage during transportation, and to affect product use. After checking the problem, we started the installation work.
Fourth, in general, the back of the stove and the wall of the net distance of not less than 15cm, side and wall spacing of not less than 20cm; if the wall is a flammable material, fire insulation layer should be added, the fire layer more than the stove The two ends and the following parts of the cooker should not be less than 10cm, more than the above part of the cooker should be not less than 80cm; the minimum distance between the cooker and the cylinder is 1m, the longest intake hose should not exceed 2m.
Fifth, the stove should be installed in a well-ventilated kitchen. Do not stack flammable materials under or around the cooker. It is easy to cause fire hazards. The kitchen area should not be less than 2 square meters, and the indoor height should not be less than 2.2 meters; the kitchen and adjacent rooms It should be well-isolated to prevent the leakage of gas from collusion.
Sixth, the desktop and the integrated cooker are relatively simple to install, and the embedded cooker is more complicated to install. When selecting the embedded installation, the opening in the specification must be strictly in accordance with the requirements of the installation position and the size of the opening. When there are flammable materials around the installation position of the cooker, thermal insulation fire prevention board must be used; the size of the opening size is appropriate and cannot be Cause the table to face the whole machine to squeeze or make the panel withstand the weight of the stove, especially the glass panel stove; when installing the stove, pay attention to the four corners of the stove panel should not be hit by hard objects.
| Gas stove installation acceptance |
First, the outer fire in the above picture is called the outer ring fire, and the central fire is called the inner ring fire. If there is a yellow flame or a pull-off flame, we will adjust the size of the damper of the cooker. First, hold the cooker by hand. At the joint between the burner and the nozzle, there are two lever-like iron pieces called the damper regulator.
Secondly, if the central fire has a yellow flame or leaves the flame, we need to adjust the iron plate in the figure below to make the flame normal.
Then press the hole to move the iron plate up and down to adjust the size of the air inlet, thus changing the state of the flame until it turns blue.
Thirdly, if the outer ring fire appears yellow flame or leaves the flame, we must adjust the position of the figure below the finger.
Pressing the iron plate up and down in the direction of the opening can adjust the size of the air inlet to change the state of the flame until the color of the flame is normal.
When the color of the flame is normal, we can begin to enjoy the delicious life of the kitchen.
Summary: Read so much about the gas stove installation process do not know if you have mastered it, in fact, the installation of gas stove is not difficult, if it is the first operation may produce some minor problems, we should also pay attention to when adjusting firepower Sometimes, it is normal for the flame to contain a little yellow flame. This may be due to the incorporation of other substances in the gas or the effects of ambient temperature and humidity during combustion. These are normal phenomena.
Gas stoves
The Infrared Panel Heater is very good and easy to use. It use electricity powered. And energy efficiency is the hightest among the heaters. It save a half than air conditioner and far better than gas heater. It is environment friendly, no pullotion, no noise and no smell. With a plug it can use enywhere in room. Some are portable type, you can move it as you want. Also it is very easy to install and don't take much money. Also the good looking can be a decorative thing in the room.
Panel Heater,Radiant Heating Panel,Infrared Panel Heater,Infrared Radiant Heating Panel
Shandong Dexiang Electrical Technology Co.,Ltd , https://www.heater-kerosene.com