Where is the burglar alarm installed better?

At present, anti-theft has received more and more attention from people. The corresponding security products, anti-theft alarms, have also entered millions of households and are used for users at any time. However, after all, not everyone is a "tech house." If an anti-theft alarm is installed improperly, it can directly affect the effect it has. So, where exactly is it installed?

The main purpose of our burglar alarm installation is theft prevention. Many burglars have detected the location of the crime for a long time before committing the crime. Therefore, the burglar alarm must be installed in a relatively hidden place to prevent the thieves from damaging. Many times, many users buy alarms and install them directly in a conspicuous place. They are intended to scare thieves but the facts are very different.

Many professional thieves know more about security equipment than we have imagined, and highly skilled thieves can easily crack burglar alarms. Therefore, we must pay attention to the use of concealed anti-theft alarm equipment, do not give the perpetrators to leave the destruction of targets and create anti-alarm conditions.

In addition, the anti-theft alarm's pipeline also needs to pay attention to concealment, in order to prevent the thieves from destroying the pipeline. However, the location of the pipeline depends mainly on the real estate developer, so that we do not have to carry out secondary construction. The pre-embedded protection pipe should be able to be flexibly connected with the backbone bridge, so as to prevent the use of a threading device as soon as possible in each case through the sheath pipe to prevent a small diameter steel cable.

Anti-theft alarms go into millions of households. In order to achieve better anti-theft effects, the installation position of the anti-theft alarm is still very important. The user pays more attention to the installation position when installing, so that the burglar alarm can ensure the security of the family property when no one is at home, so that you do not have to worry about leaving home.

About High Speed Door Accessories:

1.Driving system: High Speed Door Servo System motor and control, motor SNMA / SEJ +reducer+flang+encoder+control box

2.Other accessories: Middle aluminium bar, bottom aluminium bar, aluminium vertical track, stainless steel vertical track, brushes,round nylon strip, PVC roll, rolling steel tube complete, drum be;;s for rolling tube, side end covers, stainless steel cover, steel tubes, air bag sensor system, safety light beam, Microwave sensor 24 Gigahertz,PVC welding machine, smoke and fire sensors, PVC transparent window, magnetic loop, photocell, remote control, manual push button, sound warning alarm Led lamp traffic light

 For some main accessories, here is detain introduction:

1).24G radar sensor:

Brand: Hofic

Technology: Microwave processor

Maintain time: 0.5s

Protection: IP54

Transmitting frequency: 24.125GHz

Maximum installation height: <5meter

Transmitting power density: <5mw/cm2

Power consumption: <1W(VA)

Installation angle: 0-90°(lengthways) -30-30°(crosswise)

Supply voltage: AC&DC 12V-30V

2).Photocell:

Approval CE & ISO9001

Power supply AC/DC 12-30V

Static current 25A

Action current 40mA

Mounting distance Max 10m

NO or NC contact Done by NO./NC. contact selection              

Working environment temperature -42℃ to +45℃

Working environment humidity 10 to 90%RH

Appearance dimensions( controller) 123*50*32mm(L*W*H)

Appearance dimensions(Magic eye head) 19*13mm(L*D)

3). Remote control

Operating Voltage: AC220V/50HZ+-20%

Transmit power:≤100mW;Super regenerative module, strong anti-interference

Operating temperature:-30℃-+70℃

Working frequency: 433MHZ;transmitter 1527, millions of encoding chip

Accept sensitivity:≤110dB

Manipulation method: electric remote control

Configure the quantity: Wireless number; factory configuration transmitter two. Can be equipped with PT2272 digital decoder chip

Configure the function: Up, down, stop, anti-lock full-featured reproduction

4). Magnetic loop

Voltage: 12V AC/DC +-10% 24V 115V AC+-10% 230V

Power: <2VA

Continued electrical output: 7A / 250V AC

Frequency range: 20 to 200K Hz

Response time: infinity (factory setting) or adjust maintain time

Sensitivity: 0.01% to 0.1% divided into 3 levels

Protection level: IP30

Electromagnetic compatibility (EMC) Complies with EM50081-1 and EN50082-2

Detection loop inductance: the limit of 40uH to 100uH ideal value 80uH to 300uH

Operating temperature: -25 ℃ to 70 ℃

Storage temperature: -40 ℃ to 85 ℃

Relative humidity: <90% non-condensing

Temperature compensation: automatic compensation up to 50 ℃ / h

Connection type: 11 pin DIN rail socket

Dimensions: 41 * 78 * 85 mm (width * height * length)

Weight: 250 grams

5). manual push button

This exit switch button is made of ABS and has built-in indicator light make it looks more elegant and fashionbale. It can be widely used in public entrance gates, public door, home, office, hotel, etc.

Door Exit Button Push To Exit Switch Door Opener For Access Control  Security

Main Feature

Fashionable appearance

Made of ABS Plastic

Easy to install and operate

Used for access control

Specification

Mechanical Life: 500,000 test

Material: Plastic

6). Limit switch encoder

Voltage: DC5V-24V

Output voltage: high voltage≥85%Vcc, low voltage≤0.5V

Maximum mechanical speed:6000rpm

Anti-vibration: 50m/s,10-200HZ,XYZeach way 2 times.

Current consumption:≤30mA

Response frequency: 0-100KHZ

Protection: waterproof,oil proof,dust prevention, IP54

The output code system: binary code

Operating life: MTBF≥30000(+25℃,2000rpm)

Rotational inertia:4.0x10-8kgm²

Maximum load:radial direction20N

Axial direction:10N

Weight: about 0.4kg

High Speed Door Accessories

High Speed Door Accessories,High Speed Door,Electronic High Speed Door Accessories

Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hongfadoor.com