Wall and floor tile paving construction technology
The decoration of the wall and floor tiles is one of the indispensable decoration materials. What about the tile paving method? The wall and floor tile paving construction technology is very particular. The good craftsmanship can not only make your indoor space beautiful and smart, but also Saving a lot of money for you can save you a lot of money.
With the development of ceramic tiles, the tile paving process has been paid more and more attention by the owners. What are the precautions in the construction process of the wall and floor tiles? Next, the tile paving method is introduced:
In general, to achieve the desired laying effect, the quality of the tiles accounts for 70%, and the technique of tile laying accounts for 30%. There are no good tiles, and even if they are laid, it is difficult to achieve good results; but even if there are high quality tiles, if they are not laid, they will be wasted. So, what problems should you pay attention to when laying tiles? Xiao Bian provides some information for everyone, I hope I can help you.
First, according to the design drawings or design requirements, find out the color and pattern of the floor tiles and try them out. Pick a defective tile. This will prepare the work in the future.
Second, after the tiles are on the scene, they need to be sorted and sorted, and remember to place a safe position to avoid damage.
Third, the tiles should be soaked before laying, so as to avoid the absorption rate of the tiles, which leads to the absorption of moisture in the cement and the tight cracking (the low-water-absorbing vitrified bricks do not soak the water).
Fourth, the ground needs to use a spoon or water pipe to wet the ground floor water. Reduce dust during this operation. It also allows the ground to absorb some of the water. There will be no water shortage.
Wall and floor tile paving construction process considerations
1. First, the wall tiles should be laid from the bottom to the top, and one wall can not be attached to the top at a time, the joint is generally 1~3 mm; the second is to deal with the flatness of the wall before the paving, to deal with the crack; the third is the bonding material The application is to be slightly above the circumference, and the surface is fixed with a rubber hammer to prevent air from accumulating in the bonding layer. At the same time, horizontal testing is required. Fourth, the bonding material should be properly stirred. Generally, the ratio of cement to sand on the wall is 1:4, and the ratio of cement to sand on the ground is 1:3.
2. The ground should be leveled. Some civil construction grounds are not flat. In this case, everyone should flatten the uneven areas with cement mortar. When laying, you can frame the surrounding tiles with different colors (thinner colors), while the tiles in the frame are lighter. Of course, the kitchen and the toilet floor must have a slope, in order to facilitate drainage.
3. Tile decoration Another thing to pay attention to is the handling of the waterproof layer. The wall in the kitchen and toilet area should be highly regarded. Because the replacement of the tiles usually destroys the original cement sand pad waterproof layer. The remedy is to apply a layer of asphalt waterproofing layer before placing the tiles. The white cement filled between the tiles should also be replenished.
4. The brick surface should be flattened, the angle should be accurate, the interface should be on the line; the tile should be soaked for half a day before use; the toilet floor should have a proper bevel, and the water-free tile interface should be cleaned with white paint after sweeping white cement. Do not leave cement stains on the brick surface; cover the brick surface with cardboard after the floor tiles are finished, and walk on the brick surface at least 24 hours later.
Tile paving acceptance criteria
1. Pay attention to whether the floor tiles need to be laid out or laid in a uniform direction.
2. The flatness of the floor tiles shall be inspected with a 2 meter level. The error shall not exceed 0.5 mm, the height difference between adjacent bricks shall not exceed 0.5 mm, and the straightness of the gap shall be 3 mm. When the floor tiles are laid, other types of work shall not be polluted and shall not be artificially stepped on. After the completion of the floor tiles, the seams will be cleaned 24 hours a day, cleaned and cured.
3, the floor tile hollow phenomenon is controlled within 3%, the empty drum on the main channel must be reworked, 3% single finger single corner corner hollow, the whole block should not be empty.
4. After the floor tiles are finished and the flatness is checked for errors, empty drums, chromatic aberrations, etc., cover all the thick cardboard or plywood, old carpet, etc., and the joints must be tightly wrapped with wide paper tape to prevent debris from entering.
5. Under normal circumstances, the level of the floor tiles is allowed to have an error of 2 mm, the gap of the floor tiles must be the same, the diagonals of the bricks and bricks should be flat (allowing an error of 0.3 mm), and the bricks and bricks of the kitchen and the wall are removed. The corner should be leveled, and the level (allowing 1 mm error) and the verticality (allowing 2 mm error) should be achieved. If the bathroom and balcony floor tiles need to consider floor drain, the slope should be placed first. If there is no special reason, there must be no Water.
6. After the wall tiles and floor tiles are finished, use “caulking agent†or “white cement†to fill the wet mortar.
7. Whether the gap of the brick surface is uniform, the joints are even and tidy, the brick joint does not exceed 1mm, and the ceramic chip error does not exceed 0.8cm.
8. Whether the washroom, balcony and kitchen floor tiles with floor drain have sufficient self-drainage inclination.
9. Whether the brick surface has broken and collapsed angles.
10. Whether the direction of the tile is correct or not.
11. Whether the position of the tile and waist line is correct, there is no deviation or height error. [Follow the WeChat public number "Jiuzheng Ceramics Network" ; pay attention to surprises, scan the code to see the poor wages of the ceramic enterprises, stop the kiln and other major events! Jiuzheng ceramics network exchange group: 80123558 】
The main uses of carbide burrs:
Finish machining of various metal mold cavities; craft engraving of various metals and non-metals, engraving of craft gifts; cleaning up flash and welds of casting, forging, and welding parts, such as machine foundries, shipyards
Etc.; chamfering and rounding of various mechanical parts and processing of grooves, finishing of the inner hole surface of mechanical parts, etc.
Carbide Burr,Tungsten Carbide Cutting Tool,Double Machine Tool,Grinding Stone
Behappy Crafts (suzhou)Co.,Ltd , https://www.jshaoyue.com