Operation sandblasting machine should pay attention to the following details
2023-06-10 13:08:32
First, the amount of sand is small, or even not sand: sand material in the sand storage tank is consumed, turn off the gas, and slowly add the appropriate sand material on it.
Second, the blasting machine sand blasting gun may be blocked: stop after gas, go to the next nozzle to see if there is no foreign body, and if any foreign matter will be cleaned on the line; there is to see whether the sand material is dry, sand material is too wet It can also cause plugging, so the compressed air must be dry.
Third, the sandblasting pipe is blocked: the pipe is blocked by the spoilage, stop the gas off, the nozzle is first taken off, and then open the sandblasting machine, use the high pressure gas of the air compressor to blow out the foreign matter; still have no effect, then it is necessary Remove the pipe, clean it or replace it with a new one.
Fourth, the abrasive combination of sandblasting abrasives does not produce sand. This cleans the spray gun nozzle, and the sandblasting abrasive is poured out. After drying, it can be filtered with a screen.
5. The large amount of water generated by the compressed air of the air compressor matched with the sandblasting machine will not only cause the sand material to be wet, but also cause the wall of the sandblasting pipe to be damp and adhere to the sand material and slowly block the pipeline. Therefore, this should be avoided. When things happen, it's best to have a dryer.
Sixth, sandblasting abrasive without filter causes large foreign matter or uneven sand particles into the sand valve, this should first turn off the thrust device, adjust the sand valve all open, after the pressure tank rushed to open the sandblasting machine, with strong air pressure to the foreign body Or agglomeration of sand material is eliminated; if not, you can only remove the sand adjuster, put the sand out, and then retract the sand adjustment equipment; then filter the sand material and add it again.
Seven, add sand too much one time, sand overload can also cause blockage and can not pressurize sand; so when adding sand, we must pay attention to the amount of appropriate, and slowly added.
Second, the blasting machine sand blasting gun may be blocked: stop after gas, go to the next nozzle to see if there is no foreign body, and if any foreign matter will be cleaned on the line; there is to see whether the sand material is dry, sand material is too wet It can also cause plugging, so the compressed air must be dry.
Third, the sandblasting pipe is blocked: the pipe is blocked by the spoilage, stop the gas off, the nozzle is first taken off, and then open the sandblasting machine, use the high pressure gas of the air compressor to blow out the foreign matter; still have no effect, then it is necessary Remove the pipe, clean it or replace it with a new one.
Fourth, the abrasive combination of sandblasting abrasives does not produce sand. This cleans the spray gun nozzle, and the sandblasting abrasive is poured out. After drying, it can be filtered with a screen.
5. The large amount of water generated by the compressed air of the air compressor matched with the sandblasting machine will not only cause the sand material to be wet, but also cause the wall of the sandblasting pipe to be damp and adhere to the sand material and slowly block the pipeline. Therefore, this should be avoided. When things happen, it's best to have a dryer.
Sixth, sandblasting abrasive without filter causes large foreign matter or uneven sand particles into the sand valve, this should first turn off the thrust device, adjust the sand valve all open, after the pressure tank rushed to open the sandblasting machine, with strong air pressure to the foreign body Or agglomeration of sand material is eliminated; if not, you can only remove the sand adjuster, put the sand out, and then retract the sand adjustment equipment; then filter the sand material and add it again.
Seven, add sand too much one time, sand overload can also cause blockage and can not pressurize sand; so when adding sand, we must pay attention to the amount of appropriate, and slowly added.
Buffer ring - identify KVK seal
The company produces and sells buffer ring industrial seals, and more information about the latest professional product parameters, real-time quotations, market conditions, high-quality commodity wholesale, suppliers and other information related to buffer ring industrial seals.
ZXS SEALING PRODUCTS FACTORY , https://www.zxs-seal.com