Solid wood floor six weapons of destruction
Renovation is a big event for every family. If you are deceived in the process, the small home will not be comfortable even if it is decorated in a luxurious way. Many consumers don't understand the situation before signing a contract, and designers are usually "you don't ask, even if you know." At the same time, the home improvement package is difficult to meet the individualized decoration, its fixed main material brand and style, the choice of freedom is not high.
1. Laminate flooring
Laminate flooring maintenance is much simpler than solid wood flooring. When cleaning the floor, be careful to keep the floor dry. Do not rinse with plenty of water. Take care to avoid long-term flooding of the floor. Use a neutral detergent when cleaning stains to avoid direct sunlight, rain, moisture, etc. In addition, paying attention to indoor ventilation and maintaining indoor temperature are also beneficial to extend the life of the floor. Reinforced flooring does not require painting and waxing. Unlike solid wood flooring, avoid sanding and polishing.
2, solid wood flooring
Improper installation and use of solid wood flooring can cause quality problems in qualified products. When maintenanceing the solid wood floor, pay attention to the drying and cleaning of the floor. When laying solid wood flooring, if there is no moisture treatment, the bathroom and the room floor are not isolated, it will affect the life of the floor. Being wet with water or scrubbing with alkaline water or soapy water will destroy the brightness of the paint. In the summer, there is no attention to the curtains, so that the floor in front of the bed will be discolored and cracked after exposure to sunlight. The temperature of the air conditioner is too low, causing the temperature to change too much during the day and night, causing the floor to expand or contract excessively, causing deformation and cracking of the floor.
During the use of the floor, if individual floors are found to be shelled or peeled off, the floor should be taken in time, the old glue and ash should be removed, and the new glue should be compacted. Waxing once a month is also the best maintenance method, but wipe the water vapor and stains before waxing.
3, solid wood composite floor
The maintenance of parquet is simpler than solid wood flooring. Keep the floor dry and clean. Do not mop the floor with a mop. Do not use alkaline water or soapy water to effectively protect the floor.
If the air in the home is dry, the mop can be wet or put a basin of water on the heater, or humidifier can be used to humidify. Try to avoid sun exposure, so as to prevent the surface paint from aging and cracking under ultraviolet light for a long time. Inadvertent staining of the surface of the board should be removed in time. If there is oil, use a rag, warm water and a small amount of washing powder to scrub. In the case of drugs or pigments, they must be removed before the stains penetrate the surface of the wood.
Try to avoid contact with water for a long time on the floor, especially if it is not in contact with hot water. If there is hot water on the floor, dry it in time. It is best to take the wax once every three months. Before the waxing, the stain on the surface of the floor should be cleaned and waxed frequently to maintain the smoothness of the floor and extend the service life of the floor. Avoid sharp objects scratching the ground, do not place too hot things on the floor, try to avoid dragging heavy furniture.
Summer heat floor is the same as "heat summer"
In the hot and hot weather, the most common problem of the floor is to shrink the seam, because in the high temperature state, the moisture inside the wood is easily volatilized, which causes the floor volume to shrink, which leads to the widening of the gap at the floor joint, and even the tongue is severe. Detach, crack, etc.
Enclosed space and continuous high temperature are the main culprit for the wooden floor. The renovated new home was left unattended for a long time, and the inside of the house was closed and airtight, which made the indoor temperature high, and the house was no different from the drying kiln. Under such conditions, the moisture content of the floor is constantly evaporating, and severe shrinkage is unavoidable.
Some people say, "Since the temperature is so terrible, open the air conditioner and lower the temperature!" But I don't know, the air conditioner is equivalent to a dehumidifier. When people stay in the air-conditioned room for a long time, they will feel particularly dry, as is the case with wood. Long-time air conditioning blows against the floor and causes shrinkage.
In addition, the wooden floor is also afraid of the sun. Many floor seams occur on the edge of the balcony or on the side of the window. Exposure may also cause the paint film to foam, discolor, or even fall off. After the wood has been cut down, it still has some living characteristics, so you should be careful when treating the floor.
If you install a wooden floor, you must have someone to stay. If you can't stay right away, you should always keep ventilation and ventilation. Try not to blow the air conditioner against the floor, and feel that the indoor drying can be properly humidified. You should pull out the curtains when you are out, and avoid direct sunlight on the floor.
Flap wheel adhesive glue Feature:
1. Excellent adhesion to Flap Disc , flap wheel, phenolic emery cloth, ceramics, electroplated metal, water sandpaper, iron core, fiberglass cloth, circuit board
2. High temperature resistance, able to work in an environment around 160~200℃ for a long time, and the adhesion strength is less damaged
3. Good toughness, this single component glue can withstand thermal shock and stress shock within the range of -30~140℃
4. Better flow stop and seepage resistance, no sag after heating and curing
5. The coefficient of expansion is small, and the bond of dissimilar materials will be loose and fall off when the temperature changes.
6. Especially suitable for occasions with high requirements for high temperature adhesion and sudden stress.
7. Curing performance: (The following data is obtained under the experimental environment of room temperature 30℃ and humidity 70%, for reference only)
8. Three storage instructions: flap wheel resin adhesive should be stored in a low temperature, dry place. If stored in a freezer, please wait until the product returns to room temperature (25°C) before using it.
9. Product features: We have more than three years of professional glue production experience, and the formula has been carefully developed by the company's technical staff. The current production technology is mature and stable. With the widespread use of automatic machines, the glue produced by our company has been widely used throughout the country and has received unanimous praise and recommendations. Sincerely welcome new and old customers to try and purchase!
The related abrasive products we can supply is Flap Disc Adhesive , Bonded Abrasives , and Abrasive Machine such as Flap Disc Making Machine,Abrasive Belt Making Machine, Flap Wheel Machine , Polishing Machine ,Sanding Disc Machine, if you have any needs about abrasive tools, please kindly feel free to contact us.
Flap Wheels Adhesive Glue,Flap Wheel Adhesive Glue,White Color Flap Wheel Glue,Epoxy Resin For Flap Wheel
Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.jiadingabrasive.com