Notice of the 5th Zhengzhou International Superhard Materials and Products Seminar
2024-06-15 07:06:29
Sponsored by China Machine Tool & Tool Industry Association Superhard Materials Branch and National Superhard Materials and Products Engineering Technology Research Center, China Machine Tool & Tool Industry Association Superhard Materials Branch, Zhengzhou Abrasives Grinding Research Institute, the 5th Zhengzhou International Super The Seminar on Hard Materials and Products will be held in Zhengzhou from September 5th to September 7th, 2008. It will commemorate the 45th anniversary of the birth of synthetic diamonds in China. The Secretariat of the Preparatory Committee will invite a wide range of essays from industry professionals. The paper will be published by the publishing house. Please take time out in your busy schedule to continue to care, support and guide the healthy development of the industry.
The relevant papers are as follows:
First, the content of the paper:
1. The review article requires that the scientific and technological achievements obtained in the past five years be the main focus, highlighting the theory of progress, the status quo of the industry, the direction of development and its level at the international and domestic levels. Relevant data should be detailed and reliable, and the speculative data should be based on full.
2. The papers for individual research should clarify the conditions of the materials, equipment and instruments used, and should have relevant comparative data. The conclusions should be clear and have guiding significance for the development of the industry.
3, the scope of the paper can be: synthetic diamond, cubic boron nitride, polycrystalline, thin (thick) film, nano-diamond, all kinds of tools, all kinds of raw and auxiliary materials, all kinds of equipment and instruments. The theory, test, process and method of manufacturing, application and testing of superhard materials and products can be used.
Second, the submission requirements:
1. The manuscript and picture should be clear. It is best to use electronic manuscript. The image scanning requires more than 300 lines. If it is impossible to scan, you can send pictures. Please note if the picture needs to be recovered.
2. All manuscript requirements have not been published, and the number of words is preferably 3000~5000 words. The chapters are divided by numbers: 1, 2, 1.1, 1.2, etc., as in the first chapter of the first chapter, the first content is used: 1.2.1.
3. Deadline for the deadline: April 30, 2008. Author's brief introduction and abstract of the papers should be submitted before January 31, 2008. 4. Please send the manuscript to the person in charge of the project and the secretariat of the association. Contact person: Li Zhihong 1383711129
Address: 121 Huashan Road, Zhengzhou City, China Post Code: 450013
Telephone fax http:// E-mail: .cn;
The person in charge of the special report, the draft of the draft and the reviewer and contact information:
Wang Qinsheng super hard material and related materials 13338836861
Sun Yuchao building materials processing tools and related materials 13503161053
Liu Mingyao, machining tools and related materials 13613807228
Yang Kaihua drilling tools and related materials 13886105515
Guo Hua special equipment 13959798006
Wang wise, other, 13933507636
The relevant papers are as follows:
First, the content of the paper:
1. The review article requires that the scientific and technological achievements obtained in the past five years be the main focus, highlighting the theory of progress, the status quo of the industry, the direction of development and its level at the international and domestic levels. Relevant data should be detailed and reliable, and the speculative data should be based on full.
2. The papers for individual research should clarify the conditions of the materials, equipment and instruments used, and should have relevant comparative data. The conclusions should be clear and have guiding significance for the development of the industry.
3, the scope of the paper can be: synthetic diamond, cubic boron nitride, polycrystalline, thin (thick) film, nano-diamond, all kinds of tools, all kinds of raw and auxiliary materials, all kinds of equipment and instruments. The theory, test, process and method of manufacturing, application and testing of superhard materials and products can be used.
Second, the submission requirements:
1. The manuscript and picture should be clear. It is best to use electronic manuscript. The image scanning requires more than 300 lines. If it is impossible to scan, you can send pictures. Please note if the picture needs to be recovered.
2. All manuscript requirements have not been published, and the number of words is preferably 3000~5000 words. The chapters are divided by numbers: 1, 2, 1.1, 1.2, etc., as in the first chapter of the first chapter, the first content is used: 1.2.1.
3. Deadline for the deadline: April 30, 2008. Author's brief introduction and abstract of the papers should be submitted before January 31, 2008. 4. Please send the manuscript to the person in charge of the project and the secretariat of the association. Contact person: Li Zhihong 1383711129
Address: 121 Huashan Road, Zhengzhou City, China Post Code: 450013
Telephone fax http:// E-mail: .cn;
The person in charge of the special report, the draft of the draft and the reviewer and contact information:
Wang Qinsheng super hard material and related materials 13338836861
Sun Yuchao building materials processing tools and related materials 13503161053
Liu Mingyao, machining tools and related materials 13613807228
Yang Kaihua drilling tools and related materials 13886105515
Guo Hua special equipment 13959798006
Wang wise, other, 13933507636
Yantai Ciso Lubrication Technology Co.,LTD , https://www.cisolubrication.com