How to install tap faucet maintenance considerations
In the life, the faucet plays a very big role. The faucet, though small, is an indispensable item in every family. The frequency of use of the faucet is very high. Basically, the faucet is used every day in daily life. How can the faucet be maintained for a longer period of time under such a high-frequency use condition? To use the faucet for a longer period of time, Keeping the light bright as new, it is time to add and maintain. The following Xiao Bian will introduce how to install faucets and faucets for maintenance.
How to install a tap
The first step: First, prepare tools: screwdrivers, wrenches, and pliers. If you only replace parts (such as seals), then prepare this part. Then close the main valve.
Step 2: Remove the small screw above or behind the faucet handle and remove the handle that is attached to the faucet body. Some of the faucet screws are hidden under metal buttons, plastic buttons, or plastic tabs. When the button is opened, the handle screws on the top are visible. For taps that have been in use for a long time, the screws may become tight due to rust, etc., and some oil may be dripped in.
The third step: If the screws are hidden in the hole, it is recommended to first observe with a hand, mainly to see what is the mouth of the fixing screw, cross or a word, and then use the corresponding screwdriver to loosen. The screw of a few brand faucets is an internal square hole (such as Moen). This type of screw removal is troublesome. When using an alternative tool, special care must be taken not to damage the screw opening. When the screw is loosened, the handle can be removed.
Step 4: At this time, what you are seeing is a big copper nut. After removing the nut with a large movable wrench, you can remove the valve plug from the faucet. Observe whether the copper plane under the spool is not smooth or has fine sand grains, and remove it cleanly.
Water tap maintenance considerations
1. When the air temperature is lower than zero, if you find that the handle of the faucet handle is abnormal, you must use hot water to shower the bathroom product until it feels normal. Otherwise, it will affect the service life of the valve core.
2. The phenomenon of water dripping after the faucet is turned off is due to the presence of water in the cavity after the faucet is closed. It is a normal phenomenon. If there is a dripping situation for more than ten minutes, it is a leak, indicating that the product has quality problems.
3, because the water contains trace amounts of carbonic acid, and easy to form scale on the metal surface evaporation will have a corrosive effect on the faucet surface, which will affect the cleaning and service life of the faucet. So always use a soft cotton cloth or sponge with neutral soap water to wipe the surface of the faucet, (Caution: do not wipe with corrosive or acidic substances), then dry the surface with a soft cloth. Do not use metal filaments or scouring pads with hard particles. In addition, must not hit with the hard object so as to damage the surface of the nozzle.
4, switch taps do not force too much, homeopathic gently turn. Even traditional taps don't need to be screwed to death. In particular, do not use the handle as a handrail to support or use it. Many people are accustomed to making certain efforts to close the tap after using the faucet. This is very undesirable. This will not only prevent leaks, but will cause damage to the seal valve, leading to lax closure.
5, small water flow to clear impurities. In the case of water pressure not lower than 0.02mpa, if the amount of water found is reduced, it may be blocked inside the faucet. The solution is to use a wrench to gently unscrew the water nozzle screen cover at the water outlet of the faucet. After cleaning the impurities, carefully install it. Generally, it can be restored.
Faucet cleaning tips
1. Use a soft cloth to apply toothpaste to clean the surface, then clean the surface with clean water. Do not use alkaline cleaners or use scouring pads or steel balls to try to avoid damage to the plating surface.
2, single-handle faucet in the use of the process, to slowly open and close, double-handle faucet can not be closed too dead, otherwise it will make the sealing plug off, caused by the can not stop, can not stop the water.
3, the outlet part of the general will have foaming device (also known as foaming device, not the same as the faucet, foaming device is also the same), because of water quality problems, often make the faucet use a period of time after the small amount of water, this may be because The foamer is blocked by debris, and the foamer can be screwed off with clear water or a needle to clarify the debris.
4, some leading surface plating process is quite thick, but also pay attention to its maintenance and protection, because the coating can not withstand the hard object touch or friction, so when in use, avoid contact with hard objects such as rings.
Editor's summary: The instructions on how to install the faucet and faucet are introduced here, and I hope to help everyone. If you want to know more about yourself, you can follow the information on this site.
How to install a faucet
Actmix®Polymer-bound Pre-dispersed Rubber Chemicals and addivitives
Polymer-bound pre-dispersed rubber chemicals and additives are generally used for the automotive sealing strips, rubber hose, conveyor belt, damping, sealing etc rubber technical parts, and rubber tyres; which has mixed with the EPDM, SBR, NBR, ACM, ECO or IR. These kind of Pre-dispersed Rubber Additives are more and more popular because of the excellent dispersion and dust-free than powder form rubber chemicals.
Advantage of Actmix®Polymer-bound pre-dispersed rubber chemicals and additives:
· 1. Excellent dispersibility in the rubber compound.
· 2. Dust less & Non moisture absorption.
· 3. Saving mixing time.
· 4. Stable physical properties.
· 5. Convenient to auto measuring procedures.
· 6. Safer and healthier to operators.
Actmix®Pre-dispersed rubber chemicals and additives masterbatch product range:
· 1. Thiazole, Thiuram, Dithiocarbamate, Guandine and Thiourea accelerators.
· 2. Vulcanizing agent
· 3. Anti-oxidant and Scorching retarders
· 4. Blowing Agent and promoter
· 6. Non-Nitrosaminee Accelerator. ZDTP-50, TP-50, Retarder E-80,TBzTD-70 etc.
Pre-dispersed Rubber Additives
Pre-dispersed Rubber Additives,Pre-dispersed Masterbatch Rubber Additive,Pre-Dispersed Polymer Bound rubber,Pre-dispersed Rubber Accelerator
Ningbo Actmix Rubber Chemicals Co., Ltd. , http://www.actmixchemicals.com