How to decorate the room

The quantity room is the first step in house decoration. Although this link is small, it is very necessary and important. Measuring rooms is not just as simple as measuring data. Traditional rooms take only 10 minutes, but it takes at least 60 minutes to reach a professional standard room. Designers go to the site to measure the actual situation of the interior and exterior of the house and the environment, which is a solid foundation for high-quality home improvement. Next small series for everyone to introduce how to decorate the amount of housing and the role of decoration room.

How to decorate the room

1. Starting from the door of the house, start painting along the left side of the door until it is drawn to the right side of the door, sketching a sketch on white paper. Note that the standard for the first step is that the general plan of the house can be obtained, including the inner edge of the house and all the walls in the house. No need to pay too much attention to angles, proportions, etc. (This is no original floor plan, if you have a floor plan you can ignore this step)

2, simply handle the sketch. According to people's habits, when painting the interior wall of a room, the thickness of the wall must be taken out smoothly. Therefore, in this second step, the thickness of the bearing wall is changed to a straight line, and the wall that can be collapsed in the room (non-bearing wall) will retain its thickness no matter if you decide to break it or not.

3. Use a tape measure to accurately measure the length of each representative on the sketch. Use a pen next to the mark. It is recommended to use centimeters as the unit (professionals use millimeters as the unit. Individuals do not have to be professional).

4, windows, doors, heating. A total of three items are measured on the plane and then added to the sketch. Geothermal friends seem to be lazy

5. Congratulations on the initial level of housing sketches! Breathing first, the road is long and long, and there is still a lot of measurement work to do.

6. Carefully search for and place all the plumbing valves, gas pipes, gas meters, switches, sockets, lamp holders, heating pipes, and vent pipes that you can find on the sketch. Because you can find it on the surface, so you basically find the tube. The dark pipe can only know the location at this time, and it will be ignored temporarily.

7, analysis of water, gas, heating, ventilation four. Find the waterway and gas head that enters the room. If there is a main water switch in the room, it is best. Please pay attention to the position of the gas meter and the direction of the gas pipe. The original decoration of different houses is also different. These four items of mine have upper and lower imports and exports. Therefore, the location of the import and export, the diameter, and the distance between the side walls must be accurately measured and marked on the map.

8. Analyze the circuit. Find the head of the circuit that enters the room. If there is the best total circuit switch in the room. Accurately position measurements on sketches.

9. Use a tape measure to measure the height of the house. If there are different floors, please note. Generally only the top floor of the house will be different in height.

10. Take a large number of house interior photos with a digital camera.

The role of decoration room

1, understand the house detailed size data

Through accurate understanding of the length, width, height of each room in the house, and the location of doors, windows, air conditioners, and heating, the quantity room will have a direct impact on the quotations of the decoration.

2. Understand the advantages and disadvantages of the housing structure

Through on-site measurement, the designer will carefully observe the location and orientation of the house. As well as the surrounding environmental conditions, whether the noise is too large, how the air quality, lighting, etc., will directly affect the design of the latter period. If there are some situations where the house pattern or the external environment is not good, you need to make up for it.

3, to ensure the quality of the late housing renovation

Only accurate measurement rooms can be used to make accurate designs. In the latter stage of construction, it cannot be realized because the dimensions are incorrect, and design changes or project changes are required. Some projects such as the launching of water, heating, and gas, if they are not measured or measured inaccurately, may result in returning or replacement of toilets, basins, etc., which have not been installed due to incorrect dimensions.

4, to facilitate the designer to communicate with the owner on the ground

When a room is weighed, the designer and the owner will usually be on the scene. If the owner has a certain idea about the design of the house, they can communicate with the designer to see if the ideas are feasible and communicate effectively. In addition, if the owner needs to order the main material in advance, it also needs to communicate with the designer on site and make a decision.

Editor's summary: How to decorate the room and how to decorate the room is introduced here, and I hope to help everyone. If you want to know more related information, you can pay attention to this website information.

How to measure the amount of room decoration

This column mainly shows the parts of the crawler Excavator Final Drive.The Final Drive includes two parts: a Travel Motor and a Travel Gearbox.

We are a professional manufacturer of hydraulic accessories for crawler excavators Professionally provided aftermarket customers with various brands of crawler excavator Final Drive, Travel motor, Travel Gearbox, Swing Device , Swing Motor , Swing Gearbox ,Hydraulic Pump, Main Control Valve and other accessories.Strictly controlling the quality acceptance of each product Standards to ensure high-quality qualified export of each product.At the same time, we can customize the production services of the products through the drawings according to customer needs, and make every effort to make the perfect product in the mind of each customer.

If you want to know more about our products in more detail, please click on the product details to see more information about product quality, price, packaging, transportation, etc., or you can directly click on Contact Now on the page to talk to us directly. Looking forward to starting long-term business cooperation with you!

Final Drive

Excavator Final Drive,Excavator Spare Parts,Excavator Final Drive Parts,Mini Excavator Final Drive

Jining Juheng Hydraulic Machinery Co., Ltd. , https://www.juheng-cn.com