Hardware common sense - purchase of hinges
Hinges and concealed hinges are the keys to all kinds of furniture. Because the hinges are turned on and off more than 10 times a day in people's lives, a good or bad hinge hinges on the performance of your furniture. You also need to pay attention to the hinge hardware in your home. Basically, the hinge can be distinguished from the following aspects.
Brand Shop: Meigu Hardware
1, the surface: look at the surface of the product is smooth, if you see the scratches and deformation, is the use of waste (edge ​​material) produced, this kind of hinge ugly appearance, so that your furniture is no grade. Surface treatment: Most of the hinges are nickel-plated, but now due to the low cost of JS, only a thin layer of nickel is plated. The real hinge should be plated with a layer of acid copper before the nickel plating, which is very good Rust, tips: to teach everyone a way to distinguish whether there is copper plating: If JS does not oppose the situation can be used to draw a knife, to see if you can see the yellow copper layer, there is a more intuitive way is to look at the hinge Inside the cup, the hinge cup is recessed. This is also the most difficult place for plating. If the cup shows the same black water performance or iron color, it proves that the plating is very thin, and there is no copper plating, if the cup The brightness of the color is close to other parts, and the plating pass. Isn't it simple?
2, switch performance: We all know that the hinge is a key to the role of a switch, so this is very important, Guan Jian takes the outer spring and inner spring of the hinge, as well as rivet assembly. The outer spring is a spring piece, and the inner spring is a spring bar. It must undergo a certain heat treatment. It is too hard to break. It is too soft to close the door, and some JS purchase low-priced spring accessories, which can not close the door plate well, or the spring breaks off the door plate. . Tips: When buying a hinge (except for a hydraulic hinge), manually closing the hinge and listening to the sound of the hinge closing, is it crisp? Clear media is good, if it is a dull sound, it proves that the spring force is not enough, and there is a problem with the thickness of the material. Is the hinge cup loose? If there is loose evidence that rivet riveting is not tight, it is easy to fall off. Closed several times to see the indentation in the cup is not obvious. If it is obvious that there is a problem with the thickness of the cup, it is easy to "explode the cup."
3, screws: general hinge comes with two screws, are the adjustment screws, up and down adjustment screws, front and rear adjustment screws, some new hinges are also left and right adjustment screws, which is now the so-called three-dimensional adjustment hinge, generally with two adjustments Work station is enough. Tips: Use a screwdriver to adjust the screw up and down three or four times with point force, and then take the screw down to see if the hinge arm is damaged because the hinge arm is formed of iron material and is not as hard as a screw. , easy to wear, and if the accuracy of the factory tapping is not enough, it is easy to slip the wire, or screwed the situation. Front and rear adjustment screws are also some tests.
Flat hinges generally have four bearings. The quality of the flat hinge hinges on the quality of the bearing. Relatively speaking, the larger the diameter of the bearing, the better. The thicker the siding, the better. The hand holds the hinge one piece, allowing the other piece to slide freely, evenly. And it's slower. The spring (pipe) hinge has a full cover, a half cover, and no cover, and is used for three different connection methods for the door and the cabinet. Choosing the spring hinge is mainly to look for the brand. The spring leaf of the small brand hinge is prone to aging and fatigue, causing the door to droop. The stainless steel and steel plate hinges have thin walls, but they have good toughness and are not easily broken. Although the thick cast iron hinges, but easy to break, and some businesses deliberately deceive consumers, saying that the thicker and more expensive wall panels, in fact, different materials. When choosing a spring hinge, be aware that there should be no lack of adjusting screws on the hinge, because this screw is not easy to match and has not been sold.
The thickness of the panel hinge wall is related to the weight of the door leaf. Generally, the thickness of the panel hinge hinge wall should be 3.2 MM or more. Most of the 10 yuan a flat hinge does not have full bearings, usually two really two false. The price of spring hinges is quite different. The well-known brands have thicker sidings and fine workmanship; the small brands have relatively thin sidings and rough workmanship. The glass hinge has the middle shaft and the upper and lower shafts. The middle shaft needs to be punched and used less and less; the upper and lower shafts do not need to be punched, which is the choice of most consumers. The glass hinges are equipped with glass nails and glass holders. There are two kinds of stainless steel and stainless steel plating. All stainless steel is more expensive.
Hardware Selection Wardrobe Brand Wooden Door Brand Glass Stainless Steel Switch Furniture Door Price Glass Door Glass Furniture Glass Door
Filament Woven Geotextile,Pp Filament Woven Geotextile,Woven Polypropylene Geotextile,Polypropylene Geotextile
Shandong Jinruixiang Geotextile Material Co., Ltd , https://www.jrxgeosynthetics.com