Decoration can not ignore the details

>>>Decoration 12 traps break the trick

1. The partition of the shoe cabinet should not be the head, leaving a little space for the ash of the shoe to leak to the bottom. Install lights above the sink and gas stove. When determining the location of a bathroom floor drain, you must first think about it and measure the size. The floor drain is best located on one side of the brick. If it is in the middle of the brick, the floor drain will not be the lowest point regardless of how the brick is inclined.

2. The bathroom air conditioning sockets are not designed to switch. In particular, bathroom electric water heaters are suitable for a two-stage switch with a plug. If you want to turn off the electric heat, it is dangerous to pull the plug.

3. The treatment of the positive corner of the brick is, in the final analysis, the level of the worker. If the level of workers is good and the tools for grinding tiles are good, they should not hesitate to choose to grind the 45-degree angle. From the effect point of view, as long as the grinding is good, the practice of grinding the angle of 45 degrees is the most beautiful! If the level of the workers is really not good, then you still choose to use Yangkoo. Because of the poor 45-degree angle of grinding, it is not as good as using the effect of a positive angle strip.

4. It is also very important to test the pressure of the pipes after arranging the pipes. During the test, everyone must be present, and the test time should be at least 30 minutes. The conditions are permissible, preferably one hour. Ten kilograms of pressurization, and finally there is no reduction to pass the test.

5. When the plastic steel door must be considered the size of the plastic steel door frame protruding wall, inform the installer, making the final door frame and the finished tile wall is flat, this is not only beautiful, but also good for hygiene.

6. Carpenter's bag door covers and Mason's tiling are also to be matched. When wrapping the door, consider whether the following floor (either side of the door on either side of the floor) should be tiled or leveled with other cement mortar. Because the door covers are nailed to the floor if they are nailed before applying the tiles, if the cement and the door cover are stained when cement is used in the future, it will cause the door cover to be watery and moldy.

7. The bottom of the mattress and the bed board must be breathable, the bed board is generally the best with a fir board.

8. Make paint as much as possible with paper tape.

9. Buy lighting to pay attention: generally try to use glass, stainless steel, copper or wood (shelf). Do not buy any other plating on the iron plating, ah, what kind of paint ah, like, easy to fade.

10. The basin uses ceramic pots as much as possible.

Experience on cement glass switch paint decoration design glass tile glass door bathroom design bathroom door size bathroom tile bathroom size bathroom door tile adhesive

1. Product introduction

   Coal-based Column Denitrification Column Activated Carbon is cylindrical black particles. It has many characters, such as high porosity, high sulfur capacity, high desulfurization efficiency, large surface area, light weight, strong adsorption capacity, wear resistance, good water resistance, low air resistance, easy regeneration, not easy to break under high pressure etc. It is a commonly used in adsorbent.

2. Adsorption purification principle and process

   Coal-based denitrification Activated Carbon is divided into large pores (pore size greater than 50nrrt), the middle hole (pore size between 2 ~ 50nm) and micro-pore (pore size less than 2nm) three categories.

The denitrification activated carbon is by active carbon`s adsorption and catalytic activity of activated carbon. The strong catalytic effect of the active carbon for sulfur dioxide in gas, and a small amount of Oxygen in the oxidation reaction, the reaction of elemental S adsorbed the surface of activated carbon. When activated carbon desulfurization agent the adsorption reaches saturation, the desulfurization efficiency decreased obviously, it must carry on the regeneration. The regeneration of active carbon adsorption depends on the material, sulphur began to melt under atmospheric pressure is 190 degrees, 440 degrees Celsius will sublimate into gas, therefore, the general use of superheated steam temperature of about 450-500 degrees Celsius for the regeneration of activated carbon desulfurization agent. When the desulfurization agent reach high temperature, the elemental sulfur separate out activated carbon, the precipitation of sulfur into sulfur recovery pool, water cooled to form solid sulfur.

Column Denitrification Column Activated Carbon

Activated Carbon,Column Denitrification Column Activated Carbon,Air Purification Activated Carbon

Ningxia XingKai Silicon Industry Co., Ltd. , http://www.xingkaisic.com