Home>Bearing knowledge>The correct way to install tapered roller bearings and pump shaft bearings

/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Correct installation of tapered roller bearings and pump shaft bearings

---

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

First, the bearing device:
The bearing device must be carried out under boring and hygienic environmental conditions. Before the device, carefully check the cooperation appearance of the shaft and the outer casing, the end face of the shoulder, the groove and the processing quality of the joint appearance. It is necessary to carefully remove all the cooperation and appearance. Remove the burr; it is necessary to remove the sand from the unprocessed appearance of the casting.
Before the bearing device, it should be cleaned with gasoline or kerosene; it should be used after boring; and it should be excellent and smooth; the bearing should be smooth and smooth; the oil should be smooth. When the grease is smooth, it should be free from impurities, oxidation and rust. Smooth grease with excellent function such as extreme pressure. Smooth grease filling capacity is 30%-60% of bearing and bearing housing volume; not too much. Double row tapered roller bearing and water pump shaft bearing with sealing layout have been filled with smooth grease Users can use it directly; no more can be cleared.
When bearing the device; it is necessary to apply equal pressure on the circumference of the end face of the ferrule; press the ferrule; do not directly hit the bearing end face with the number one thing; avoid damage to the bearing. Under the condition of small interference; Press the sleeve on the end face of the bearing ring at normal temperature; hit the sleeve with the head; press the sleeve evenly through the sleeve. If it is a large-scale device; use a hydraulic press. When pressing in; ensure the outer ring end face and The shoulder end face of the outer casing; the inner ring end face and the end face of the shaft shoulder are pressed tightly; no gap is allowed.
When the interference is large; you can use oil bath heating or induction heating to install the device; the heating temperature is 80 °C-100 °C; the maximum can not exceed 120 °C. Together; use nuts or other appropriate means to tighten the bearing ; to avoid the shortening of the width direction of the bearing after cooling, resulting in a gap between the ferrule and the shoulder.
The single-row tapered roller bearing device should be adjusted for the clearance at the end. The clearance value should be determined in detail according to the different operating conditions and the cooperative interference amount. If necessary, the experimental determination should be made. Double row tapered roller bearing And the pump shaft bearing has been adjusted at the factory clearance; the device does not need to be adjusted.
After the bearing device, the rotation test should be carried out; firstly, it should be used for rotating shaft or bearing box; if it is not abnormal; it will be driven without load and low speed by power; then gradually increase the rotation speed and load according to the working condition; and detect noise, oscillation and temperature rise. Found abnormal; should stop the operation and check. After the operation experiment is normal, it can be delivered.
Second, the disassembly of the bearing:
After the bearing is removed, it is recommended to continue to use it; it should be properly disassembled. Disassemble the ferrule of the interference cooperation; only pull the force on the ferrule; never allow the detachment force to pass through the tumbling body; otherwise it will roll Both the body and the raceway will be crushed.
Third, the operating environment of the bearing:
According to the application site, operating conditions and environmental conditions, the standard scale and accuracy are selected; the suitable bearing is the condition for ensuring the bearing life and reliability.
1. Application: Tapered roller bearings are suitable for accepting radial and axial combined loads with radial loads; usually used with two sets of bearings; first and foremost for the front and rear wheels of the car, automatic bevel gears, differential Transmission parts such as reducer and reducer.
2, promise speed: in the correct, smooth and outstanding environment; the maximum speed of the bearing is 0. 3-0. 5 times. Normally under normal conditions; the limit speed of 0.2 times is the most suitable.
3, promised skew angle: tapered roller bearings usually do not allow the shaft to be skewed relative to the shell hole; if there is skew; the maximum does not exceed 2'.
4, promise temperature: in the normal load; and the smoothing agent has high temperature resistance; and smooth and plentiful conditions; usually the bearing promises to work at -30 ° C -150 ° C ambient temperature.

---

Recommend to friends comments close window

Bearing related knowledge

Ceramic bearing clarification LYC deep groove ball bearing function detailed solution - SKF bearing type to explore the characteristics of tapered roller bearing KOYO outer spherical bearing

This article links to http://
Please indicate the bearing network http://

Previous:KOYO angular touch bearing Next: NSK bearing lubrication tips

Pneumatic Filter Regulator

Pneumatic Filter: remove water, dirt and other harmful debris from an air system. This is often the first step in improving the air quality.

Pneumatic Regulator: adjust and control the air pressure of a system to ensure that down-line components do not exceed their maximum operating pressures. This is the second step in the FRL system.

Airtac Pneumatic Filter Regulator, SMC Pneumatic Filter Regulator, FESTO Pneumatic Filter Regulator

NINGBO BRANDO HARDWARE CO.,LTD , https://www.brandopneumatic.com