CNC cutting machine safety regulations and precautions
2023-07-25 07:08:47
First, prevent electric shock
1. When the power is on or the machine is running, do not touch any electrical components in the electrical cabinet and console. Otherwise, electric shock may occur.
2. Do not operate any switch knob with wet hands to prevent electric shock.
3. Please do not energize the line or replace the electrical components. Otherwise, it may cause electric shock or injury.
4. Maintenance personnel with corresponding technical qualifications, and the equipment can be repaired only in strict accordance with the electrical maintenance technical requirements. In case of accidents.
Second, to prevent fire
1. The working materials used by the cutting machine are flammable gases such as acetylene, propane, liquefied gas and other gases. Therefore, it is necessary to periodically check whether the entire air path is sealed.
2. The gas source of the cutting machine should be kept away from the open flame, and place normal carbon dioxide or other appropriate fire extinguishing devices near it.
3. The operator shall timely control the fire when adjusting the fire to avoid a fire.
Third, to prevent damage
1. When the cutting machine is running, pay attention to whether there are people or other objects in front so as to avoid hitting.
2. After each cutting is completed, the torch should be raised to a higher position so as not to touch the steel plate and damage the cutting torch.
3, mechanical maintenance personnel in the maintenance should ensure that the machine is stopped working. And hang up warning signs to prevent the sudden operation of the machine and human accidents.
4. When the machine is running for a long time, you must not directly touch the heat sink and other heat-generating devices on the module to avoid burns.
Fourth, operation precautions
1. Before starting the machine, check whether there is a leak in the machine pipe, and if there is a leak, it will never start.
2. After starting the machine, check whether there are any obstructions on the working surface and the guide rails. If there are obstacles, they must be excluded.
3, the operator can not leave the job freely, non-operators must not start the machine at will.
4. In the event of an emergency during operation, immediately press the red emergency stop switch to prevent accidents.
5, maintenance of CNC cutting machine should pay attention to the command and coordination of technicians.
6. Close all air valves before shutting down, and put the remaining air in the air.
7. If the pipeline is found to be tempered, it must be powered off immediately.
1. When the power is on or the machine is running, do not touch any electrical components in the electrical cabinet and console. Otherwise, electric shock may occur.
2. Do not operate any switch knob with wet hands to prevent electric shock.
3. Please do not energize the line or replace the electrical components. Otherwise, it may cause electric shock or injury.
4. Maintenance personnel with corresponding technical qualifications, and the equipment can be repaired only in strict accordance with the electrical maintenance technical requirements. In case of accidents.
Second, to prevent fire
1. The working materials used by the cutting machine are flammable gases such as acetylene, propane, liquefied gas and other gases. Therefore, it is necessary to periodically check whether the entire air path is sealed.
2. The gas source of the cutting machine should be kept away from the open flame, and place normal carbon dioxide or other appropriate fire extinguishing devices near it.
3. The operator shall timely control the fire when adjusting the fire to avoid a fire.
Third, to prevent damage
1. When the cutting machine is running, pay attention to whether there are people or other objects in front so as to avoid hitting.
2. After each cutting is completed, the torch should be raised to a higher position so as not to touch the steel plate and damage the cutting torch.
3, mechanical maintenance personnel in the maintenance should ensure that the machine is stopped working. And hang up warning signs to prevent the sudden operation of the machine and human accidents.
4. When the machine is running for a long time, you must not directly touch the heat sink and other heat-generating devices on the module to avoid burns.
Fourth, operation precautions
1. Before starting the machine, check whether there is a leak in the machine pipe, and if there is a leak, it will never start.
2. After starting the machine, check whether there are any obstructions on the working surface and the guide rails. If there are obstacles, they must be excluded.
3, the operator can not leave the job freely, non-operators must not start the machine at will.
4. In the event of an emergency during operation, immediately press the red emergency stop switch to prevent accidents.
5, maintenance of CNC cutting machine should pay attention to the command and coordination of technicians.
6. Close all air valves before shutting down, and put the remaining air in the air.
7. If the pipeline is found to be tempered, it must be powered off immediately.
Acr Gear Pump,Gear Pumps For Oil,Small Gear Pump For Oil,Manual Gear Oil Pump
Hengshui Yuanhan Trading Co.,Ltd , https://www.hengshuiyuanhanpump.com