Bathtub maintenance, big battle, bathroom maintenance, small classroom
First, gently treat surface stains
You can use a waste soft-bristled toothbrush to wash the surface with bleaching powder to remove stains and eliminate mold. If you encounter a hard-to-scratch stain, you can also use a half of lemon to rub the salt, or you can use a soft toothbrush to apply a toothpaste with a whitening function. The turpentine is also very good at this time. For scale, the products used for cleaning toilets on weekdays are very useful. If you don't like the pungent taste, you can use lemon and white vinegar as a natural method. Do not use cleaners with fading, especially when the bathroom is colored. For mold and fungal disease-causing bacteria, rinse with bleaching water and peroxygen water and dry immediately.
Second, timely repair scars
The bathtub is installed so that it does not move by itself. If you need to move the position, you must contact a professional. Do not hit or hit the surface with a hard object, causing bruises or scratches. If you need to repair the faint or scratched part of the acrylic bathtub, wipe it with a clean rag and mix the colorless automatic grinding solution, then apply a layer of colorless protective wax. Do not wax on the area where you have settled, so as to prevent it from slipping.
Third, weekly cleaning
1. Use a sponge or flannel when cleaning the acrylic bathtub. Do not use coarse cloth or scouring pad. Do not use any cleaning agent containing granular objects. It is best to avoid direct sunlight and high temperature cigarette butts. Use a mild detergent (such as dishwashing detergent), do not use abrasive cleaner.
2, acrylic bathtub can also be cleaned with glass water. The cast iron bathtub should be thoroughly rinsed with clean water after each use and wiped dry with a soft cloth. If you encounter stubborn stains, use a small amount of abrasive cleaner to clean. Clean the bottom non-slip surface with a soft nylon brush. Do not scrub with a steel ball, wire brush or abrasive sponge.
3. The jacuzzi system should be flushed twice a month. Adjust the nozzle clockwise to the fully closed position to prevent air leaks. Inject warm water into the bathtub to 2 inches above the highest nozzle, or leave the water in the bathtub after use. Add two tablespoons of low foaming powdered dishwashing detergent and a small amount of household bleach to the water. Turn the jacuzzi on for 5 to 10 minutes, then close, drain the water, and then rinse the bathtub surface with water. When the bathtub is in a hot and humid state for a long time, it will also breed a lot of bacteria. Sometimes it is cleaned and the surface looks clean. In fact, there are still many bacteria. It is recommended to wipe the surface of the bathtub with boiling water regularly. Do not use disinfectant water casually, because disinfecting water does not necessarily kill mold and fungi.
Fourth, handling pipeline blockage and disinfection
The pipeline should be cleaned once or twice a week to remove the taste and to prevent bacterial growth. You can use a product that cleans the sewers and pour it into the sewer. After 5 minutes, it should be cleaned. Be careful not to use it in metal pipes. If the bathtub is blocked, first close the water removal valve, then put a proper amount of tap water in the bathtub; place the rubber suction device (to clear the toilet) on the water removal valve; while opening the water removal valve, suffocate the basin or The overflow hole of the bathtub; then quickly attracting up and down, sucking out the dirt or hair and cleaning it off in time. In the case of a serious blockage, it can be repeated several times until the dredge is clean.
LED point light source is a new kind of energy conservation and environmental protection decorative light, using LED cold light source, the built-in microcomputer chip, can be arbitrary programming control, multiple synchronous change, monochromatic changes can also be realized synchronous colorful gradient, jump, scanning, running water light color change effect and multiple LED point light source form a lattice screen.All kinds of pictures, text and animation effects can be changed. It is a supplement of linear light source and flood lighting, which can meet the design requirements of the point line surface.
Product size
Led Point Lamp,Blue Point Led Lamp,Led Point Ovale,Led Blue Point
Jiangsu chengxu Electric Group Co., Ltd , https://www.chengxulightings.com