Ancient Castle Oak Laminate Flooring

Product Structure




Details






Color Code











Surface Finish
 





Packing












Q&A
Q: What would be a suitable sub‐floor for Piano‐finished laminate flooring?
A: Plywood or OSB single or double layer sub‐floor under layment combination. Existing floor surface including, hardwood, lumber or engineered wood flooring. Linoleum, PVC or resilient vinyl flooring. Existing floor surface must be permanently attached to the sub‐floor.
Attention: concrete sub‐floors must always be covered with a moisture barrier. Moisture barrier must be installed prior to putting Piano‐Finished flooring over substrate.

Q: What's the best method to clean my floors?
A: Normal vacuuming, dry mopping and or sweeping will usually keep your floor clean. If stubborn spots still remain, use a laminate floor cleaner. Do not use any cleaning agents containing wax, oil or polish, left over residue from agents can leave a dull film on the floor. Remove stubborn stains carefully with acetone based fingernail polish remover. Never use scouring products!

Q: How can I prevent my floor from scratching?
A: Use wide bearing, non staining floor protectors, such as hard plastic or felt protectors for chair legs and table legs. Use either a natural or color‐fast doormat outside, and inside each entrance to your home to prevent dirt, sand, grit and other substances from being tracked onto the floor. Do not use steel wool or scouring powder, could scratch the floor.

Q: Is the laminate flooring required acclimatizes?
A: Yes, let the planks acclimatize for 48 hours in the unopened packaging at the room temperature, in the middle of the room where the floor is to be installed.

Q: Is an expansion gap required for my laminate flooring?
A: Room humidity can vary according to the season, so it is vital that the floor is able to expand and contract. For this reason, make sure you leave an expansion joint of minimum 8 to 10mm(5/16" to 3/8") on all sides of the floor, around pipes, thresholds and under doors. Transition pieces should be used in doorways that are four feet wide or less.

Q: Can laminate flooring be installed on stairs?
A: Yes. You'll need to fully adhere the flooring to the stairs without using foam underlayment and follow the special installation instructions for stair installations.



Our service
Professional trading team is always ready to service for you
Good faith on cooperation, for high quality, competitive price 
Installation will be suggested professionally
OEM/ODM
Delivery within 45  days after the order  
All the products delivering after the  tough inspection  
Best price based quality in the line ,Goods passed  SGS well guaranteed
Good after-sale service would be available
 


Free sample can be available.
You are interested in our product, but hesitate because of first cooperate? No problem.
Just feel free to contact us and free sample will be sent to your address in the first time .


Product Structure




Details






Color Code











Surface Finish
 





Packing












Q&A
Q: What would be a suitable sub‐floor for Piano‐finished laminate flooring?
A: Plywood or OSB single or double layer sub‐floor under layment combination. Existing floor surface including, hardwood, lumber or engineered wood flooring. Linoleum, PVC or resilient vinyl flooring. Existing floor surface must be permanently attached to the sub‐floor.
Attention: concrete sub‐floors must always be covered with a moisture barrier. Moisture barrier must be installed prior to putting Piano‐Finished flooring over substrate.

Q: What's the best method to clean my floors?
A: Normal vacuuming, dry mopping and or sweeping will usually keep your floor clean. If stubborn spots still remain, use a laminate floor cleaner. Do not use any cleaning agents containing wax, oil or polish, left over residue from agents can leave a dull film on the floor. Remove stubborn stains carefully with acetone based fingernail polish remover. Never use scouring products!

Q: How can I prevent my floor from scratching?
A: Use wide bearing, non staining floor protectors, such as hard plastic or felt protectors for chair legs and table legs. Use either a natural or color‐fast doormat outside, and inside each entrance to your home to prevent dirt, sand, grit and other substances from being tracked onto the floor. Do not use steel wool or scouring powder, could scratch the floor.

Q: Is the laminate flooring required acclimatizes?
A: Yes, let the planks acclimatize for 48 hours in the unopened packaging at the room temperature, in the middle of the room where the floor is to be installed.

Q: Is an expansion gap required for my laminate flooring?
A: Room humidity can vary according to the season, so it is vital that the floor is able to expand and contract. For this reason, make sure you leave an expansion joint of minimum 8 to 10mm(5/16" to 3/8") on all sides of the floor, around pipes, thresholds and under doors. Transition pieces should be used in doorways that are four feet wide or less.

Q: Can laminate flooring be installed on stairs?
A: Yes. You'll need to fully adhere the flooring to the stairs without using foam underlayment and follow the special installation instructions for stair installations.



Our service
Professional trading team is always ready to service for you
Good faith on cooperation, for high quality, competitive price 
Installation will be suggested professionally
OEM/ODM
Delivery within 45  days after the order  
All the products delivering after the  tough inspection  
Best price based quality in the line ,Goods passed  SGS well guaranteed
Good after-sale service would be available
 


Free sample can be available.
You are interested in our product, but hesitate because of first cooperate? No problem.
Just feel free to contact us and free sample will be sent to your address in the first time .

IECEx Approved Coriolis Mass Flow Meter

Zhejiang Sealand Technology Co., Ltd. is a trustworthy manufacturer of Mass Flow Transmitter, Coriolis Mass Flow Transmitter, Coriolis Mass Flow Sensor, Mass Flow Sensor & Mass Flow Sensor Coriolis, ATEX, IECEx & CE approved.

The meter can be connected with computer as follows. Connect the meter and computer with a USB-to-RS485 converter( converter A+ end to transmitter A+ end, B- to B-, and GND to GDN); turn to device manager of the computer to check COM port connected with meter. Start the software, select the right COM port and click Connect; do not change any other parameters (if you do not know the right one, click Automatic options on the left, click Connect, plug & unplug the transmitter, and then check if it is connected). You can click Connect on the tool bar to disconnect or connect again. It will shown Connected/Not Connected at the bottom of this interface.

The flow direction is settable. There are 4 options, forward(default), reverse, absolute value & bi-direction. There is a direction mark on the sensor. Forward means the same direction with the mark on sensor, the meter will only count the flow in this direction; reverse means the opposite direction of the mark, the meter will only count the reverse direction; bidirectional means that the meter will measure both directions, it increases when it is forward and decreases when reverse; absolute means it increases no matter it is forward or reverse.

Mass Flow Transmitter, Coriolis Mass Flow Transmitter, Coriolis Mass Flow Sensor, Mass Flow Sensor, Mass Flow Sensor Coriolis

Zhejiang Sealand Technology Co., Ltd. , https://www.sealandflowmeters.com